Skip to content
Auxiliary Valves

PS-401

Pressure relief valve

Pressure relief valve that opens when the system is overloaded, sending excess flow back to the tank and limiting circuit pressure.

PS-401 · Pressure relief valve PS-401 – Pressure relief valve
410barMax. working pressure
1/2Body size
1Connection type: Pressure relief valve
1Product code

Features and benefits

Technical specifications

  • Operating temperature−20 °C/+100 °C
  • Working pressureUp to 350 bar
  • DimensionsFrom 1/2"
  • Flow rateUp to 50 l/min
  • Thread optionsBSP
  • SealNBR
  • MaterialAluminium

Selection

How is the product code read?

There is a single model; the code contains no options.

PS–401
Model Model: 1/2″ port, M24×1,5 body, aluminum
Series Pressure relief valve

How it works

How does the valve work?

Normally closed. When system pressure reaches the set value, the valve opens and sends the excess flow to the tank, keeping pressure constant.

Normal operation

Oil goes to the circuit; the tank line is closed.

Overpressure

The valve opens and excess oil returns to the tank.

When is it needed?

In every circuit with a pump; it protects the pump and hoses when the cylinder reaches the end of its stroke or the load jams.

Setting

The opening pressure is set with the adjusting screw and locked with the lock nut.

Selection

How it differs from other auxiliary valves.

Scroll the table sideways to see all columns
ValveWhat does it do?When?
FUVAdjusts flow in one direction, free in the reverseCylinder speed in one direction only (e.g. lowering)
FCVAdjusts flow rate in both directionsCylinder / motor speed in both directions
CVAllows flow in one direction onlyPreventing backflow
TLVLocks the cylinder in both directionsHolding a load in position for a long time
HPVShuts off flow if the hose burstsSafety on load-lifting cylinders
PS-401Discharges excess pressure to the tankProtecting the system from overload

Instructions and warnings

Before use.

Correct use

For long life and reliable sealing

  1. Do not expose to abnormal operating conditions (for example oscillation, pressure shocks, water hammer, cavitation, solid and abrasive particles).

Warnings

Read before installation and use

  • Do not touch the valve when the operating temperature is below -20 °C or above +50 °C.
  • Make sure the system pressure is below the maximum working pressure.
  • Make sure all connection surfaces are clean so that dirt and dust do not build up in the circuit.
  • Make sure the mounting parts are on the same axis and fully connected.
  • Make sure the Oleocon product you have selected is suitable for your system's temperature, material and pressure requirements.
  • For any other questions, contact the Oleocon technical support team.

Installation and use

Filtration, viscosity, temperature.

Scroll the table sideways to see all columns
ConditionOleocon PS-401
FiltrationPending
ViscosityPending
Oil temperature−20 … +100 °C
BodyAluminium
SealingNBR

Installation and use

A wrongly fitted valve is useless.

Caution
  1. Install as close to the pump as possible

    The relief valve must be between the pump outlet and the control valve; there must be no valve that can be shut off in between.

  2. Do not restrict the tank line

    The tank port must go directly to the tank. Back pressure in the tank line is added to the opening pressure.

  3. Make the setting with a pressure gauge

    While turning the adjusting screw, the pressure is read on the pressure gauge; when the setting is done, the lock nut is tightened.

  4. Do not run continuously open

    If the valve continuously discharges oil, the oil heats up quickly. The valve should stay closed in normal operation.

Installation and use

Port names and correct placement.

  1. 01

    Pressure line (P)

    The line coming from the pump outlet; the valve limits the pressure in this line.

  2. 02

    Tank line (T)

    The line through which the opened valve sends oil to the tank; it goes directly to the tank.

  3. 03

    Pressure gauge port

    To read the pressure during adjustment.

  4. 04

    Setting and locking

    Set the adjusting screw to the desired pressure and tighten the lock nut.

FAQ

The questions users ask most.

Where on the pump is the relief valve fitted?

Between the pump outlet and the control valve; the tank port is connected directly to the tank.

How do I change the setting pressure?

By loosening the lock nut and turning the adjusting screw; check the value with a pressure gauge.

What if there is another relief valve in the circuit?

If the control valve has an internal relief, the PS-401 can be set to a higher value as backup protection.

Can't find your question?Our technical team answers every question about the series.Contact technical support

Applications

Where is PS-401 used?

All application areas 8

Downloads

Catalogs, Technical Data and CAD.

You may also like

Related series

Can't find the size or connection you need in the list?

Send us the code or a technical drawing; we will get back to you with a suitable product and price.

Request a quote

Fill in the form and our team will get back to you as soon as possible.

Cookie preference

We use measurement cookies to improve the site. They only run with your consent. Cookie Policy

Reject Accept